In the hopes of preserving the data and disk inside, I'm actually eager to follow instructions this time around. I've looked high and low for info on cracking the case, but I haven't found any instructions. I'd like to crack open the enclosure for my d2 quadra so that I can get out the disk and see if data can be recovered once I pop it in another enclosure or drop it in a sata dock. The application icon will appear in the system tray and LaCie Network Assistant will automatically. (But when those supplies are reconnected to other drives, those drives have no problems and the bricks don't make the hissing and clicking sound). Select LaCie Network Assistant in Start > Programs. And this time, it's not the external power supply - I swapped the cord with working power supplies from other drives and each time I use them with the failed drive, I get a clicking sound in the external supply. I suspect the drive inside my failed d2 Quadra is fine and the data intact, but the unit is failing to power up. I've had easily a dozen LaCie drives over the years - beginning with a 160 megabyte model more than a decade ago - and like other users, I've had my share of power supply and drive failures.īut I've never cracked the enclosure of a d2, and I need to now. Swapping the hard drive then utilizing fvdw-sl resolved this.I know this is an old thread, but I thought I'd throw this out there just in case. The original drives heads were crashing so that was an obvious sound. The drive had a failed boot script, as well as a failed hard drive. So yeah what you are saying sounds right. At that point I thought I figured out some way to get it to boot into its recovery mode that I couldn't access. The drive remained on my network with a pingable IP but i couldn't find any services running on that IP. I then halted the LNA and its sftp program, so it wouldn't attempt to recover and reboot the drive. So tinkering a bit I ran LNA waited for it to find the drive ran arp -a and saw the mac address associated to an ip on my network. LNA recovery would time out and fail (the drive once again not appearing on the network). ![]() The drive would reboot going back to a quick flashing blue. Then when attempting the recovery the led would flash red one time Moment later it would state that it found the drive The LNA, like you said must interrupt something because the recovery would load. ![]() With the lacie drive powered on quick flashing the blue led. I couldn't find the cloudbox's mac address which was labeled on the sticker inside. Ps a fast blinking blue led means that the boot script is hanging (so not necessarily that your disk is dead)īefore coming across fvdw-sl and playing with LNA I was scanning my local network for devices. I rather would think that the boot script of the lacie firmware has a special mode when booting to detect the assistant and interrupt boots to upload the recovery file.īut on a new disk nothing is present, so I might be wrong It could mean that the bootloader of the cloudbox responded to the LNA (similar tool as fvdw-sl console) and interupted boot and tries to upload the capsule, but I doubt if the bootloader has the capability to install the firmware. What do you mean with that ? that it found it after you stated it ? I'm glad these resources existed as it saved yet another piece of tech designed to rot in a landfill after a year. Very functional tool but still required a lot of reading on this forum as well as disabling firewalls isolating the nas and laptop on a switch etc.ĭoes LNA require an originally formatted lacie drive to function? what is the point of that? Followed the steps for loading the firmware within the fvdw-sl-console. Googled more and came across plugout and fvdw-sl. ![]() Still the nas drive was flashing blue and would reboot automatically when the LNA recovery would fail. I saw that it pulled an ip and was now pingable. ![]() I ran the tool again with cmd open this time I did an arp -a when the LNA says it found the drive and was attempting to recover. So the LNA tool managed to find the drive even though it was not appearing on my network. quick blue flashing led after it rebooted its self. I ran the recovery thinking wham bam this tool is the real deal and will bring it back to life. Googled around and found the Lacie network assistant software for windows as well as the "CloudBox_2.6.10.2.capsule" file that lacie network assistant LNA uses for recovery. The cloudbox would not dhcp and come online with a replaced drive or the dead drive. I replaced the internal hard drive with a spare sata seagate barracuda.Īttempted to boot the drive again with the same result. Not the slow blue flashing you see on some youtube videos. It would boot and the blue led was flashing quickly.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |